Skip to Store Area:

Socal Logo

Propex Heatsource HS2800 Twin Outlet Marine Kit

Double click on above image to view full picture

Zoom Out
Zoom In

More Views

HS2800M2

Propex Heatsource HS2800 Twin Outlet Marine Kit

Email to a Friend

Be the first to review this product

Availability: In stock.

£919.00
Add Items to Basket Add to Basket

Quick Overview

Propex Heatsource HS2800 Twin Outlet Marine Kit


Applications
Propex Heatsource blown air systems are used in many applications throughout the world, these include Motorhomes, Caravans, Boats, Cranes, Horseboxes, Mobile Workshops etc.
Control
The HS2800 is supplied as standard with a solid state electronic thermostat which automatically switches the unit on and off to maintain the desired temperature. When the room temperature drops below the selected level, the Heatsource will automatically ignite and run until the cabin reaches the selected temperature. The thermostat is an easy to fit surface mount design and integrates with the new electronics fitted to the HS2800 heater. An easy to operate, panel mounted digital timer/ thermostat specifically designed for heatsource HS2800, is also available. Unlike some heaters, there is minimal electrical current consumption during ignition, so cycling the Heatsource on and off does not have the effect of additional battery drain.
Efficiency
With forced air combustion and the Propex two stage stainless steel heatexchanger, the HS2800 is a clean and highly efficient way to heat your vehicle or boat. Air for combustion is taken from outside and passed into the combustion chamber having been mixed with gas during three aeration stages, it is ignited automatically and heats up the large surface area of the heat-exchanger.
The Heatsource HS2800 is a totally room sealed and exhaust all products of combustion externally through the neat 26mm I.D. stainless steel flue pipe. To add to the efficiency, cabin air is normally recirculated in preference to using cold air from outside. The HS2800 heaters are also very efficient on electrical current consumption. The high quality motor/fan combination and innovative current reducing electronics, both of which have been improved in the latest versions, means that even the largest HeatSource heater draws less than 2 amps during normal operation.
Quiet Operation
Propex HeatSource heaters are designed to be quiet in operation without compromising air throughput and heat output. There will always be some air noise from a system that produces a healthy throughput of air, however, by using high quality balanced fans and smooth enclosed motors with ball race bearings, noise is kept to a minimum. Noise is also unaffected by high voltage, a common occurrence with battery chargers, solar panels etc permanently wired. The micro-processor electronics regulates the motor voltage so that the fan speed does not alter from 10 to 15 volts.
Safety
Heatsource blown air heaters conform to the latest European standards for both the appliance and electronics and during this rigorous testing the focus is very much on safety. The heaters also have to comply with an enhanced version of the Electro Mechanical Compatibility Directive to ensure they do not interfere with other electronics and that they are immune from interference by other electronics. The intelligent electronics are continuously monitoring the operation of the heater to make sure everything is operating correctly and safely. This includes monitoring of the flame, case temperature, combustion airflow, gas solenoid valve and voltage. Should any of these stray outside of the predetermined levels, the heater will be switched off and the red light on the thermostat will indicate a fault by flashing a certain number of times.
Installation
The HS2800 is supplied with complete fitting kits to suit either vehicle or marine applications. In vehicles and caravans the unit is usually mounted in a bed-box or cupboard, flued downwards through the floor and out to the side of the vehicle using flexible stainless ducting. These ducts (22mm I.D. for the HS2000 and 26mm I.D. for the HS2800) are supplied as standard in lengths of 750mm for vehicles and 1 metre for boats. The ends are finished with neat stainless steel end-caps which comply with EN624. The heat is ducted to one or more outlets through tough highly flexible 60mm or 76mm ducting. In the case of multi-outlet installations, the first outlet is an open outlet with directional control and the rest are closable and are used in conjunction with the appropriate sized plastic Y-branches. Marine applications feature an attractive polished stainless steel through hull fitting which accepts the stainless steel pipes for the flue outlet and the combustion air inlet. Extra ducting and stainless steel bulkhead mounting brackets are also part of the marine fitting kits.
Features
2400w Twin outlet blown air heating kit.
Sealed Combustion System
Automatic ignition
Thermostatically Controlled
Highly Efficient
Quiet when running
Maintenance free operation
Fast warm up time
Airflow sensing detects blocked or restricted flue pipes
Self-diagnostic fault finding.
2400w Heat outlet
Available in 12v or 24v
1.8A continous running
236m3 per hour Air throughput
Gas consumption 209grams per Hour
Heater kit includes
Heater & Control system
4m ducting
1m exhaust hose
1m combustion air hose
stainless steel through hull flue fitting & bulkhead mounting bracket
1 directional vent
1 open/close vent
Y branch tee
Hose Clips
Dimensions
Width = 41.5cm
Height = 12cm
Depth = 21cm
EAN No
Manufacturer Propex Heatsource
Manufacturer Part Number HS2800 M2
Brand Propex
Colour No
Weight (kG) 31.0000
Heat Input No
Cylinder Size No

Product Tags

Use spaces to separate tags. Use single quotes (') for phrases.